6 Ways To Turn Off Speed Limit On Segway Ninebot

The speed limit is a safety feature in Segway Ninebot electric vehicles that restricts its maximum traveling velocity. Turning off this feature allows removing the preset speed cap so that the vehicle can reach higher speeds without any limitations. However, caution must be exercised as speeds above the predefined limit can impact safety and are also illegal on public roads and paths.

Have you ever wished to “Turn Off Speed Limit On Segway Ninebot” so that it travels faster and you can enjoy an exhilarating ride? Removing the factory-set speed barrier makes the vehicle attain higher velocities. This allows travelers to cruise efficiently, reach destinations sooner, and experience an adventurous ride like never before with an unrestricted Ninebot.

Once switched off, the speed restrictor is disabled giving the Segway Ninebot full acceleration capabilities. This permits attaining maximum potential from the electric motor and battery. However, safety gear must be worn and speeds must be handled responsibly on private properties alone. Operating at high velocities requires expertise and following all traffic rules is advised for legal and safe riding experience.

Manually Disabling the Speed Limiter on Segway Ninebot

The Segway Ninebot comes with a speed limiter for safety. This keeps the scooter from going too fast. But you can turn it off if you want to ride faster. To turn it off, find where the battery meets the scooter frame. There will be two wires, one red and one black. Use pliers to disconnect the red wire. Be very careful, as the scooter can now go much faster. Always wear a helmet when riding at higher speeds.

Without the speed limiter, the Segway Ninebot uses its full power. You will feel it go much quicker when you twist the throttle. But you must only do this somewhere safe like a big empty parking lot. Never turn off the limiter on busy sidewalks or roads with cars. Go very slowly at first to get used to the new speed. Make sure to reconnect the red wire when you are done, so the limiter comes back on for regular riding. Always stay in control and be aware of your surroundings when riding without limits. Safety first!

Removing Speed Limiter on Ninebot F-Series

The Ninebot F-Series electric scooters have a safety feature called a speed limiter. This limits how fast the scooter can go. But for experienced riders, the limiter can come off. Under the deck near where the stem meets the base, there is a black plastic cover. Open it to find the control board. Look for a soldered connection marked SL. Using a soldering iron, carefully melt the solder to separate the wires. Replace the cover when finished.

Now your Ninebot F-Series scooter can go faster when you twist the throttle. But only ride without the limiter in big empty spaces like parking lots. Never ride too fast on busy streets or sidewalks around people. The first few rides without the limiter, take it slowly until you know how the scooter handles at higher speeds. Always wear safety gear like a helmet. Be respectful and follow all rules of the road. Your safety and that of others needs to come first. Ride responsibly and have fun!

Check Your Firmware

Ensure your scooter’s firmware version is below DRV5.6.9. If your scooter is using DRV5.6.9 or a newer version, you may need to downgrade to an older firmware OR consider other hack methods discussed in this guide.

Verify Local Laws

Before attempting any modifications, be sure to verify your local laws and regulations, as certain modifications may be prohibited or illegal depending on your location.

Use Official Ninebot Firmware

This hacking method is designed for scooters running official Ninebot firmware. If your scooter has been flashed with custom firmware from an unofficial third-party source, this method may not be compatible.

Get the Right Tools

You will need an Android smartphone or tablet with Bluetooth 5.0 or newer, your Ninebot F-series scooter and the ScooterHacking Utility application downloaded.

Follow the Guide

• Download the ScooterHacking Utility application to your Android device.
• Power on your Ninebot F-series scooter and use the app to connect to it via Bluetooth.
• In the app, navigate to the “Tools” section and select the option to “Change region”.
• From the model selection menu, choose “Global – (Your Scooter Model)”.
• The scooter will automatically reboot with the new region selected.
• Take note of any changes in the serial number or region displayed on the scooter screen.
• If successful, place the scooter in ‘Sport’ mode to test the new top speed limit of 30 km/h.

Unlocking Ninebot Scooter Speed Using DownG App

There is a simple app you can use called DownG to unlock your Ninebot scooter’s full speed. First, download the DownG app on your phone and connect to your scooter’s Bluetooth. Open the app and go to the speed setting. You will see the current speed limit, usually 15 mph. Just slide the bar higher to raise the limit. The app changes the speed limit safely through your scooter’s software.

When you increase the speed limit with DownG, your Ninebot can now go faster when you twist the throttle. Make sure to only do this in big empty areas for safety. Never ride too fast on streets or around people. As you get used to the new speed, start slow on your first rides. Always wear a helmet and follow traffic rules. Have fun but be responsible on your faster scooter!

Removing Speed Limit of Ninebot G30 (by using XiaoFlasher app)

The Ninebot G30 scooter has a speed limit for safety. But with the XiaoFlasher app, you can change its maximum speed. First download XiaoFlasher on your phone and connect to the G30 over Bluetooth. Go into the app settings and find the speed limit option. You will see the current limit, usually 15 mph. Simply slide the bar higher to increase it. The app updates the scooter’s software safely from your phone.

Now when you ride, the G30 can go faster. But only increase speed someplace wide open, like an empty parking lot. Never ride too fast near roads, people, or cars. On your first faster rides, start slow until you know how it feels. Always wear a helmet for safety. Follow all traffic laws too. Have exciting rides with your more powerful G30, if you promise to ride carefully!

Modifying Firmware with ST-Link 

Flashing custom firmware directly onto a Ninebot scooter’s control board using an ST-Link debugging tool allows advanced modifications beyond software limits. This advanced technique carries high risks and should only be attempted by experienced tech-savvy users. Here are some important points on modifying firmware with ST-Link (risky):

• ST-Link is a debugging and programming tool used to modify firmware on devices
• With an ST-Link, you can directly connect to the Ninebot scooter’s control board and flash new firmware
• This allows unlocking maximum speed and other parameters without software limitations
• However, modifying firmware requires advanced technical skills and any mistakes could brick the scooter’s control board
• You need ST-Link hardware and software, ability to read code, and skill with command line interfaces
• Risks include permanent damage to the controller, reduced safety features, and voiding of the manufacturer’s warranty
• Only attempt if you are an experienced developer and understand all the risks of directly flashing firmware
• Modifying firmware is not recommended for average users due to the high chance of issues or SCOOTER malfunction
• Safety features removed by firmware mods like speed limit could be dangerous if not handled carefully

Requirements

ST-Link V2 Programmer: Acquire an ST-Link V2 programming device. This hardware connects your computer to the scooter’s microcontroller.

Scooter Firmware File: Obtain the official firmware package for your specific Ninebot scooter model. Verify compatibility with your scooter hardware.

ST-Link Utility Software: Download and install the ST-Link Utility program on your computer. This application interfaces with the ST-Link programmer.

Hex Editor (optional): A hex editor may be required to manually edit values within the firmware file before flashing.

Steps to Flash and Modify Speed Using ST-Link

Modifying your scooter’s firmware requires using specialized programming hardware and software to communicate directly with the scooter’s microcontroller. When done properly, these steps will allow you to flash a custom firmware file that alters parameters like top speed. Proceed with caution and read all instructions thoroughly:

Locate the Controller Board: Open the scooter and find the main controller board, typically featuring an STM32 microcontroller.

Connect the Programmer: Attach the ST-Link programmer to the appropriate pins on the controller board per the pinout for your scooter model

Install ST-Link Utility Software: If needed, download and install the ST-Link Utility on your computer.

Backup the Stock Firmware: Use the ST-Link Utility to read the current firmware from the controller as a backup in case of issues.

Modify the Firmware: Use a hex editor to locate and carefully edit values controlling speed and settings within the firmware file.

Flash the Modified Firmware: With the ST-Link Utility, flash the modified firmware onto the controller board with a stable power supply.

Test the Scooter: Reassemble and test ride the scooter to ensure the intended speed and functionality changes took effect safely.

Custom Speed Controller for Ninebot Scooters

A custom speed controller can remove the speed limit on a Ninebot scooter. It replaces the stock controller under the deck. These special controllers let riders set higher speed limits. They connect to the motor and battery instead of the normal controller. Some have dials or apps to adjust the max speed easily. Others require reprogramming skills. Custom controllers make scooters go much faster than store settings.

Installing a custom controller takes time. The stock controller must disconnect carefully. Then the new one solders to the same spots. Go slowly and follow all instructions. Test the scooter starts safely first at low speeds. Wear protective gear like a helmet for speed tests. Only ride as fast as feels safe to control. Obey all laws when riding on roads. Custom controllers let scooters go very fast, so always ride responsibly!

FAQ’s

How do you unlock the speed on a Segway-Ninebot?

There are several ways to remove the speed limiter on a Ninebot scooter, either using apps on your phone or more advanced methods. Always ride safely at higher speeds and wear a helmet.

How do I change my Ninebot speed?

You can increase your Ninebot’s speed using apps like DownG which safely adjust the software limit through Bluetooth. Always ride carefully at first on open courses.

Why does my Ninebot only go 15 mph?

Ninebot electric scooters come with a default speed limit of 15 mph for safety purposes. The manufacturer implements this to prevent unsafe higher speeds.

What is the fastest mode on a Ninebot scooter?

Most Ninebot scooter models have a “Sport” mode that provides the maximum attainable speed, though firmware or app adjustments may allow riding even faster.

What are the 3 modes on an electric scooter?

Most electric scooters have Eco, ride, and sport modes – with eco being the slowest, the ride being regular speed, and sport providing maximum power and speed if limits are not enabled.

Conclusion

Segway Ninebot’s Commitment to Safety and Promoting Responsible Riding is exemplified through its dedication to providing guidelines for scooter usage. Be careful if you remove the speed limiter, as scooters can now go much faster than before. Only ride without limits in big empty spaces like parking lots. Never ride too fast near streets, sidewalks, or people. Practice starting slowly on the first faster rides. Get used to the new speed and feel in control. Always follow traffic rules for your safety and others. Wear protective gear like helmets for speed unlocking. Ride smart and stay responsible on your Ninebot scooter.

Some ways to unlock speed were explained. Consider each method and remain safe. Only skilled riders should flash the firmware. Apps are safer to use. Never hurt yourself or others by riding too dangerously fast. Follow all scooter hacking guides carefully. Most of all, use your new faster scooter wisely in appropriate areas. Have exciting rides while protecting yourself and others.