Hiboy S2 Scooter Won’t Turn On?

The Hiboy S2 electric scooter is a popular personal transportation device, but sometimes it won’t turn on when you try to use it. There are a few potential reasons why your Hiboy S2 scooter won’t power up. The most likely culprits are an empty battery, a loose wire connection, or a faulty power button.

“Hiboy S2 Scooter Won’t Turn On?” This frustrating question gets asked a lot by Hiboy S2 owners when their scooter suddenly fails to start. There are steps you can take to troubleshoot and fix the problem. Checking the basics like battery charge level, wire connections, and power button function is a good place to start. Don’t give up hope, a solution is usually found.

When a Hiboy S2 scooter won’t turn on, there are a few things to check. Make sure the battery is fully charged and the power cable is plugged in properly. Also, inspect wires for any loose connections. The power button itself could also be dirty or defective. With some basic troubleshooting, you’ll likely get your Hiboy S2 scooter back up and running. Patience and methodically testing components will help identify the specific issue.

Charging, Battery & Fuse Obstacles, not Turning-On Hiboy S2

The first thing to check if your Hiboy S2 scooter is not turning on is the battery. Make sure the battery is fully charged. Remove the battery from the scooter and plug the charger into an electrical outlet. The charger light should turn red showing it is charging the battery. It will turn green when the battery is fully charged. If Hiboy S2 Pro Is Not Charging does not solve the problem, check other areas.

Check the Battery

Take the battery out of the scooter and look at it closely. Make sure there is no damage to the outside. Press the power button on the battery to see if the LED lights come on. If they do not, the battery may need to be replaced.

Inspect the Charging Port 

Look inside the charging port on the scooter where the charger plugs in. Make sure there is no dirt or debris inside the port. Clean it out with compressed air or a small brush if needed.

Check the Power Switch

The power switch turns the scooter on and off. Make sure the switch is fully engaging when turned on. If it does not click firmly, the switch may need replacement.

Inspect the Fuses

Fuses protect the scooter’s electrical components from power surges. Remove the fuse box from under the seat to check the fuses. If a fuse is blown (broken inside), replace it with a new one of the same rating.

Fuse Location

On the Hiboy S2, the fuse box is located under the seat. Two screws hold the cover on. Remove those screws to access the fuses inside and check or replace them if needed.

Wiring & Controller Conflicts Hiboy S2 Power-up

Issue	Possible Cause	Solution
No power at all	Loose wiring connections	Check all wiring for loose or disconnected connectors, tighten or reconnect
Won’t turn on	Damaged controller	Have the controller tested or replaced by the authorized service center
Intermittent power	Faulty controller	Replace controller
Blinks error code	Software issue	Update controller software version
Buttons not responsive	Faulty wire between buttons/controller	Check wiring, reconnect or replace wire
Dim/flickering lights	Loose bulb/housing	Ensure all bulbs/lights are securely in place and connections tight
Clicking noise	Loose motor connection	Check motor wiring and tighten connections
Slow/weak acceleration	Low current from the controller	Have the controller load-tested, may need to be repaired or replaced

The main issues checked in this table are loose or faulty wiring connections, a damaged or faulty controller, software conflicts, and loose components that could cause intermittent power or other electrical errors preventing the Hiboy S2 scooter from powering on reliably.

Examine the Wiring

• Check for any cuts or abrasions in the wiring insulation that could cause shorts
• Inspect connectors for corrosion, rust or loose connections where wiring meets components
• Look for pinched wires, especially near tight bends in the frame, that may cause intermittent breaks
• Pull on wires gently to check for looseness at the connections, wires should not pull out easily
• Trace wires from the battery back to ensure they are properly connected at both ends
• Ensure wires are neatly tied and bundled with cable ties and not chafing against the frame
• Check ground wires especially, make sure they are securely fastened with screws
• Examine thicker gauge wires for the battery/motor for damage or cracks in the insulation
• Wiggle and flex wiring harnesses to check for loose wires inside the casings
• Make sure wire connectors are the correct type and size for the gauge of wire used
• Clean connectors with electrical contact cleaner and reseat wires if corrosion is found

Reset the Controller

If issues remain after checking wires, reset the controller. Turn off the power switch. Press and hold the power button, then turn the switch on while holding for 10 seconds. This resets the controller’s software. Try restarting after. If problems continue, contact the dealer. Properly resetting the controller is simple and may help.

Replace the Controller

If resetting fails, the controller may need replacing. Contact the dealer. They can test the old controller and install a new one if needed. A dealer can replace the controller quickly and correctly connect all wires. A new controller may fix issues with the scooter powering on. Call the dealer for parts replacement help.

Overheating Protection

Scooter controllers have safety features. One is overheating protection. The controller monitors its temperature during use. If it gets too hot, the protection will engage. This stops power until the controller cools down. Then it will work again. This safety stops damage from heat. Let the scooter rest if protection activates. It will return to normal once cooled fully.

Throttle & Brake Issues not Moving Hiboy S2

If the scooter is turning on but will not move forward or backward, check the throttle and brakes. These control how the motor moves the scooter. Make sure to test them on a flat, open area free of obstacles before troubleshooting.

Test the Brake Levers 

Squeeze both brake levers fully while trying to roll forward. The brakes should engage and stop movement. If one brake is not working, it may need adjustment or repair.

Dislodged Throttle Magnet/Throttle Issues (Especially with the S2 Pro) 

The throttle uses a small magnet inside to sense how far it is twisted. Check this magnet did not come loose on the S2 Pro version. Also, ensure the throttle is twisting smoothly without clicks or catches that could cause issues communicating to the controller. Try re-pairing the throttle to the controller if needed.

If the brakes and throttle all test okay, check that the controller is receiving the proper signals to engage the motor. The throttle and brake wires may need reseating at the controller. Also, ensure the controller software is updated to recognize the throttle/brake inputs correctly. With some careful checking, these issues can typically be resolved. Always ride safely and don’t operate the scooter if a problem cannot be identified and addressed.

User Manual & Professional Guidance

Consult the User Manual

• The manual has info on safe use, specs, diagrams, maintenance, and troubleshooting.
• Check manuals’ trouble codes and solutions for error messages.
• The manual provides instructions for adjustments, resets, and updates.
• Contains contact info for support and repairs.
• Review manual procedures before any repairs.

Seek Professional Help

At times, the problem could exceed what can be addressed through DIY troubleshooting:

If the aforementioned solutions fail to resolve the issue, or if you feel uneasy about attempting troubleshooting on your own, it’s advisable to seek help from a professional.

While reaching out to the manufacturer’s customer support is an option, bear in mind that it might entail a fee.

Preventive Measures for the Future

Taking some preventive measures can help avoid issues down the road. Small tasks now save bigger fixes later. Following some regular maintenance and safe practices will keep the scooter in top shape.

Regular Maintenance

• Check tires weekly for proper pressure and wear. Inflate as needed.
• Keep the scooter clean and wipe it down after every ride.
• Tighten all screws and bolts monthly to avoid vibrations loosening parts.

Proper Charging Habits

• Fully charge the scooter after every use. Don’t top-charge or let sit at very low power.
• Only use an authorized charger for the best care of the battery.
• Store scooters at around 50% charge when not in use for more than a week.

Safe Riding Conditions

• Avoid puddles, potholes, or rough surfaces that could damage the base or electronics.
• Check local laws and always wear a helmet for safety.
• Don’t carry additional weight or passengers without reinforcement.

Storage

• Keep the scooter indoors and dry when not in use.
• Store upright on its kickstand, not on its side.
• Cover the scooter if stored for more than one month. Check the battery monthly.

Regular Safety Checks

Be sure to conduct thorough safety checks before each ride.

• Inspect equipment for defects
• Verify safety gear is present and working
• Document inspection results

Following these simple tips can keep a Hiboy S2 running smoothly for many miles of fun riding.

FAQ’s

How do you turn on a Hiboy scooter?

To turn on a Hiboy scooter, you press the power button which is usually located on the baseboard near the handlebars. You will hear a beeping sound indicating the scooter is starting up.

Is there a reset button on an electric scooter?

Yes, most electric scooters have a reset button that is used to restart the scooter’s system if it encounters an error or glitch. The reset button is typically found underneath the deck near the stem of the scooter.

How do I reset my Hiboy scooter?

To reset a Hiboy scooter, press and hold the power button while simultaneously pressing the brake lever. Continue holding both buttons for 5-10 seconds until you hear a beep to indicate the reset is complete.

Why is my scooter not starting with the button?

If your scooter is not starting with the power button, it could be due to a low or drained battery, loose wiring connections, or a faulty power button. Checking these basic systems is the first step to troubleshoot the issue.

Conclusion

Solving issues with a Hiboy S2 that won’t turn on takes patience and methodical testing. Carefully checking the battery, wires, controller, and other components is key. Referring to the manual and following its guidance is important. If problems remain, then seeking professional help from an authorized dealer may be needed. They have special tools and experience to properly diagnose difficult problems.

With proper maintenance like regular safety checks, battery care, and cleaning, most Hiboy S2 owners can easily troubleshoot basic issues. Preventing future problems makes any repairs much simpler. Strong record-keeping of ride details and scooter condition also aids repairs. Taking good care keeps the Hiboy S2 scooter operating safely for transportation or recreation. Common Problems and Troubleshooting guidance is there when home remedies fall short.